RE: [SilverStreak] SS sabre logo casting

["Steve Schultheis" <sdstone@xxxxxxxxxxxxxxx>]

Well here is my part even though the Unknown Fixture" is yet to be Id'.
You might want to check on water jetting the logo? This way it can be
cut from plastic od any color or alum?
I bet it would cost way less as well
Steve

-----Original Message-----
From: sslist-admin@tompatterson.com
[mailto:sslist-admin@tompatterson.com] On Behalf Of Tom Patterson
Sent: Monday, June 02, 2008 10:13 AM
To: sslist@tompatterson.com
Subject: Re: [SilverStreak] SS sabre logo casting


Ok, lets go with Darwin's intact logos.

What I will do is go by the casting company today, and ensure that they
will 
still do this sort of thing.  I will get back to you later today with a 
confirmation.

At that point, you can send them to me at:

9123 McAfee Drive
Houston, Texas 77031

Thanks,

Tom

----- Original Message ----- 
From: "Darin Unthank" <darin@multi-pak.com>
To: <sslist@tompatterson.com>
Sent: Monday, June 02, 2008 11:04 AM
Subject: RE: [SilverStreak] SS sabre logo casting


> Tom-
>
> I'm in Los Angeles county, San Fernando Valley.  I will UPS them to 
> you. Send me your address.  My e-mail is darin@multi-pak.com
>
> Regards,
>
> Darin
>
> -----Original Message-----
> From: sslist-admin@tompatterson.com 
> [mailto:sslist-admin@tompatterson.com] On Behalf Of Tom Patterson
> Sent: Monday, June 02, 2008 8:53 AM
> To: sslist@tompatterson.com
> Subject: Re: [SilverStreak] SS sabre logo casting
>
> Hi Dan,
>
> If your logos are fully intact, they may work a little better than 
> Patti's logos.
>
> Where are you located?
>
> -Tom
>
> ----- Original Message -----
> From: "Darin Unthank" <darin@multi-pak.com>
> To: <sslist@tompatterson.com>
> Sent: Monday, June 02, 2008 10:37 AM
> Subject: RE: [SilverStreak] SS sabre logo casting
>
>
>> Tom:
>>
>> I have both the Silver Streak logo (1967) and the Sabre logo that are
> in
>> good shape.  I can send these to you.
>>
>> -----Original Message-----
>> From: sslist-admin@tompatterson.com 
>> [mailto:sslist-admin@tompatterson.com] On Behalf Of Tom Patterson
>> Sent: Sunday, June 01, 2008 4:52 PM
>> To: sslist@tompatterson.com
>> Subject: Re: [SilverStreak] SS sabre logo casting
>>
>> Anyone in the Houston area who has some logos I can borrow in order 
>> to have a mold made up?  If both front and back are the same size, 
>> then only
> one
>>
>> logo is needed.
>>
>> -Tom
>>
>> ----- Original Message -----
>> From: "Bev Harris" <zia@ix.netcom.com>
>> To: <sslist@tompatterson.com>
>> Sent: Sunday, June 01, 2008 6:49 PM
>> Subject: Re: [SilverStreak] SS sabre logo casting
>>
>>
>>> I'm interested too for my  64 Sabre.
>>> Bev
>>>
>>> On 1 Jun 2008 at 17:04, Tom Patterson wrote:
>>>
>>>
>>>> I should be able to get some of these cast here in Houston if there
>> is
>>>> any
>>>> interest.
>>>>
>>>> I had some Streamline ones done in aluminum, and they turned out
>> well.
>>>>
>>>> I would need to borrow some existing logos for the casting company
> to
>> use
>>>> to
>>>> make up molds.
>>>>
>>>> Any interest?
>>>>
>>>> -Tom
>>